Видео

This is a wonderful thing. I hope the manufacturing goes from strength to strength. I want all my tools made in Devon!

Excellent video on bandsaw set up. Very thorough! Covered every important aspect. I would add, however, a small tip; when aligning the bandsaw blade to the wheel, center the blade gullet (the deepest recess of the tooth edge) to the centerline of the wheel. The blade will look a bit off center as a whole. This brings the cutting edge closer to the center line of the wheel (not on it). This prevents the blade from wobble and fish tailing, keeping the cutting edge from wandering and always engaging the bearing wheels.

It's a shame they didn't test there lathes and they could work on there after sales service

I saw Jason at the Mid-Atlantic Symposium in Lancaster, PA USA. He really is a talented turner, trainer and jokester. I enjoyed this video almost as much at the Symposium.

Not sure if you’re still following comments, because the video was several years ago. But I’ll ask my questions and hope you are. I followed your technique and got perfect results - except - the joints are way too tight. I sanded the insides of the fingers and I can put it together but they’re still too tight for glue. Gonna need more sanding. Is it because of the wood? I’m using oak that’s 13.5mm thick.

I think Axminster should spend less time promoting their products and more time actually getting them in stock! Sanders, table saws, planers - most are out of stock with no suggestion when they'll be back in!

can make sone cool mft table tops with this !

This is terrible lmao he’s really nervous. Also, he’s wearing his safety specs on top of his head 😂

Love it! I teach kids woodworking. I’m going to have the kids make some variation of this project.

Way too fast. Also seems a worrying lack of PPE on the factory floor.

Salivating

Is the end grain on the sides or the end where you have your face plate

Pretty cool stuff. 👽

I really appreciate my Axminster tools, my favourite is my bandsaw, used daily 😊

Awesome thank you

Dizzying 🙂 A longer slower version would be of interest 🙂

All to fast don’t get to take it all in and it makes me dizzy

Great video. Good insight, made in UK. Quality testing! Core values!

1000,,,,!!!!!!!!!!!!!

you're rip cutting. Do these crosscut saws also rip cut well?

New to this Colwyn. It's always a pleasure to watch you turn.you make it look so easy.but as with anything you turn it takes time.

It´s nice to see that my working progress of my first aztomaton is so similar to yours. But I worked it out by myself, just by looking at Images of a automata and trial and error.

Einhell, Scheppach, Sip, Wen and more all sell the same thing? The saws are all noisy and buttons etc identical. Is this any different?

One of the best videos I have ever watched!! As a beginner, this video helped me clear a purpose of each tool. Extremely helpful. Thank you!!

Mini vases

I can't see me ever making a garden gate such as this but I enjoyed watching this video and as usual Jason reveals some useful tips.

At 6:15 or so there's a mention of a flat bandsaw wheel. I have the larger version of these Italian-made bandsaws (the 540), and my wheels are not crowned. I believe that means running with the teeth just off the front of the wheel/tire instead of in the middle, but if the wheels are perfectly co-planar that's difficult to achieve. Any tips for adjusting tracking on a flat-tired bandsaw?

Excellent. This is exactly what I was looking for. Just lost a large number of branches from the hurricane Beryl and thought this would be a great project.

Really well produced, thank you for putting this together!

Excellent video, more like this household stuff is really useful, and not just fine woodworking. This is smth everyone can start their woodworking journey. As many are coming to it through DIY. And when all the gates and deck chairs are done in their garden snd in their neighbours’, they are turning into make something more sophisticated. Great job, excellent presentation and perfect soundtrack!

Good work. Great instructions. Very inspirational, thank you!

Bugger - I put up a gate (bought in) a week ago! 😡 May make another hole in wall and build this gate to fill it! Great video, thank you

Hi is there any difference in the AC405ss to this one apart from the added flexi shaft or have they up graded there awful pin-less blade support clamps which let the machine down terribly thank u

Thank you for your clear explanation. And, it is much cheaper than a domino.

Sir by far the best video out there explaining what each tool does and how to do it. I’m gonna save this and run out to my rockler store and get some new tools. I’ve been using carbide scrapper and round head? Tools and I’m feeling limited.

Where can I get one of these from in 2024?

Great Video. I am going to make one of those.

❤We already have a bench grinder 2800 rpm with a 50mm Reki and a Axminster 40mm CBN wheel and find it running a bit to fast and thinking off a Axminster Professional AP200SRG 1450 rpm Grinder i want to know the C/C between the wheels the grider i have has 360mm with our own rest setup on the bench Thank You

What product did you use to make the dyes? And what did you tint them with?

Little trick from making model aeroplanes more than 5 decades ago. After glueing the paper to the frame LIGHTLY spray the inside surface with water (perfume spray is perfect) and leave to dry. The paper will shrink slightly and become much more taut and smooth.

Love this video ! thank you, you've peaked my intrest in automa ( not sure of spelling), your a very creative as well as an organized teacher who explains precicely how to assemble ,well done.

Contact no

You apologised to the Amerians for NOT being able to use BRITISH MEASURMENTS. The UK started to use Metric Measurments when we joined the EU. WE HAVE LEFT THE EUROPEAN UNION. IMPERIAL MEASUREMENTS LIKE INCHES ARE BRITISH!!!! YOU SHOULD BE GIVING ALL MEASUREMENTS IN IMPERIAL UNITS - FIRST. By all means as a courtesy to Europe it is OK to give metric measurments AFTERWARDS. How do you get things BACKWARDS?

Way too expensive, need a more affordable brand

Wow thats awesome Brendon.

prety cool but polyurethane glues work better for fingerboards

I'm just starting out with woodworking and just watching this video already gave me some nice and handy tricks. I like that it's full length, showing the whole process and not just tiny bits. I will soon make this lamp!